100% Pass Top-selling NACE-CIP1-001 Exams - New 2021 NACE Pratice Exam
CIP Level 1 Dumps NACE-CIP1-001 Exam for Full Questions - Exam Study Guide
NEW QUESTION 17
Relative humidity is
- A. the highest temperature at which moisture forms on a steel surface.
- B. a measure of the amount of moisture in the air compared to the air temperature.
- C. the lowest temperature at which moisture forms on a steel surface.
- D. a measure of the amount of moisture in the air compared to saturation level.
Answer: D
NEW QUESTION 18
A magnetic pull-off type gauge is a good choice when:
- A. When working on non-ferrous metals
- B. Accuracy is not required
- C. Performing an adhesion test
- D. When an intrinsically safe tool is required
Answer: D
NEW QUESTION 19
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Go with the majority opinion
- B. Never change his/her mind
- C. Call the supervisor
- D. Achieve consensus through negotiation
Answer: C
NEW QUESTION 20
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Call the person who wrote the specification for clarification
- B. Use the job specification as a guide
- C. Call the coating manufacturer for clarification
- D. Use the product data sheet as a guide
Answer: B
NEW QUESTION 21
Which of these tests uses a syringe?
- A. Potassium ferricyanide
- B. Sleeve test
- C. Soluble salts meter
- D. Bresle patch
Answer: D
NEW QUESTION 22
To achieve consistently accurate results with ALL alt test equipment
- A. wear gloves when sampling.
- B. wash your hands before sampling.
- C. calibrate the instrument in the field.
- D. avoid placing the sample discs on a surface.
Answer: B
NEW QUESTION 23
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Skip the checks and just record the same readings as you have been getting
- B. Keep doing the checks and consult the Owner's representative for direction
- C. Keep doing the checks regardless
- D. Skip the checks as you are. confident the blast pressure is OK
Answer: B
NEW QUESTION 24
A NACE Coating Inspector is permitted to transport coating material when:
- A. Asked to do so by the Coating Application team
- B. The Inspector should never transport coating material
- C. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
- D. Asked to do so by the Owner's Representative
Answer: B
NEW QUESTION 25
Solvents are added to coating formulations to
- A. provide color.
- B. dissolve binders and form liquid coatings.
- C. decrease film permeability.
- D. increase film permeability.
Answer: B
NEW QUESTION 26
Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT
- A. how the item was coated.
- B. what items were coated.
- C. what materials were used.
- D. when the coating will be reapplied.
Answer: A
NEW QUESTION 27
Fine cracks in the surface of a coating that rarely reach the substrate are called
- A. blistering.
- B. checking.
- C. cracking.
- D. alligatoring.
Answer: B
NEW QUESTION 28
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Localized Corrosion
- B. Galvanic Corrosion
- C. General Corrosion
- D. Atmospheric Corrosion
Answer: B
NEW QUESTION 29
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Assume the role of the Safety Inspector
- B. Act in accordance with the site safety requirements and set an example
- C. Check the credentials of the Safety Officer on site
- D. Check the PPE used by the Applicators
Answer: B
NEW QUESTION 30
ISO SA 3 is directly equivalent to:
- A. None of the above
- B. NACE No. 3/SSPC SP 6
- C. NACE No. 1/SSPC SP 5
- D. NACE No. 2/SSPC SP 10
Answer: A
NEW QUESTION 31
Osmotic blistering is most likely to occur as a result of
- A. applying tine coating too thin.
- B. overcoating a surface contaminated with chemical salts.
- C. inadequate anchor pattern/surface profile.
- D. airless spray application
Answer: D
NEW QUESTION 32
If inspectors identify issues of non-conformance during an inspection, they should
- A. perform additional tests secretly to ensure there are no other potential issues at the site
- B. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- C. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- D. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
Answer: D
NEW QUESTION 33
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A. vial lest.
- B. wet film thickness (WFT) measurement.
- C. blotter test for the presence of oil and water.
- D. dry film thickness (DEI) measurement.
Answer: C
NEW QUESTION 34
The NACE Inspector should perform tests for soluble salts:
- A. Prior to surface preparation
- B. Prior to coating application
- C. When specified
- D. After surface preparation
Answer: C
NEW QUESTION 35
......
Authentic Best resources for NACE-CIP1-001 Online Practice Exam: https://www.itcertmagic.com/NACE/real-NACE-CIP1-001-exam-prep-dumps.html
NACE-CIP1-001 Test Engine Practice Exam: https://drive.google.com/open?id=1Owe8a0UETcN5MJpQkvcM-VSzqKTOIj9-